View and Download IAME Parilla X30 cc RL overhaul manual online. Parilla X30 cc RL Engine pdf manual download. Also for: Parilla x View and Download IAME Parilla x30 cc RL-TaG assembly instructions & user manual online. Parilla x30 cc RL-TaG Engine pdf manual download. Stay connected to IAME’s social network and become a member of the IAME community. Enjoy videos and pictures; learn about upcoming events, and countless.
|Published (Last):||8 April 2004|
|PDF File Size:||13.95 Mb|
|ePub File Size:||9.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
Gear Timing Schematic Before amnual the clutch, wash with diluent ia,e shaft taper, the connecting hole on the clutch body, the clutch drum and the starter ring. Never exceed the above limits; no obligation of IAME exists in case the above limits are exceeded. Don’t have an account? The engine is suplied without oil in the gear box.
When designing this new engine, we have considered the technical solutions already adopted for the high performance engines, and the experience acquired with the TaG engines Touch and Go. Warm the engine gradually for about 5 minutes at half throttle, making some laps at low speed, gently closing and opening the carb.
Spark Plug And Thermal Degree 3. Contents of packing 1. Disconnect carburetor and clean it. Before starting the engine fill the box with SAE 30 oil.
Before assembling the paril,a, wash with diluent the shaft taper, the connecting hole on the clutch body, the clutch drum and the starter ring. Always make sure that janual springs are well hooked and in place. Don’t show me this message again. It is necessary to recharge the battery.
By pressing ‘print’ button you will iiame only current page. Page 33 The following example should clarify the procedure for the optimization of the sprocket ratio. When starting the engine, make sure that the brake pedal is fully pressed to avoid sudden accelerations. Starting the engine with a dry box will damage the gears beyond repair – Charge of the gear box: Comments to this Manuals Your Name. Seal with tape the engine inlet and exhaust.
L close the screw completely and then open: In case of breakage, replace the broken spring. Enter text from picture: When the tension drops below The final customer, in this case, can skip this section and can start reading from section 3.
Iame Parilla X30 Manuals
Table of Contents Add to my manuals Add. The external of the engine must be cleaned. Never exceed the above limit. Install The Water-cooling System 2.
Carburetor Adjustment Guide 3. In order to lenghten the battery life it is necessary though to follow a few recommendations: No obligation of IAME exists in case the above limit is exceeded. For a correct installation follow the under shown instructions. In case the flexible is damaged, metallic particles could be sucked in the engine and cause a seizure. Install The Intake Silencer 2.
In case the engine is supplied already assembled on the chassis, it is at care of the assembler to follow these instructions. The following example should clarify the procedure for the optimization of the sprocket ratio.
According to the different engine versions. Refer to the following drawing during the operations. Got it, continue to print. Install the starter ring on the clutch body by matching 12 point wrench 10 mm the three holes and the parila pin 3 screws M6.
IAME X30 Technical Information
Disconnect the battery and charge it periodically see sect. Page 32 According to the different engine versions.
Only use 5A strip fuse. This manuaal a 3 position key: Replacement Of The Starter Brushes 4. Use of different spark plugs is possible and, as a general information, we are attaching a correspondence list among spark plug of other brands, based on thermal degree which represents the capacity of the spark plug to dissipate the internal heat.
Start with an adjustment on the rich side. Install The Exhaust 2. Use of fuses with higher amperage might damage the electronic box whenever the battery polarity is reversed. Exhaust Header Assembly Fig. In case the user wishes to optimize on the track the sprocket ratio in order to achieve the best possible performance, without abusing the engine, follow the under shown recommendations. To print the manual completely, please, download it.
To install the water pump belts it is necessary to remove the rear axle.